首页力学固体力学弹性力学 26 薄板弯曲问题1.PPT

26 薄板弯曲问题1.PPT

页数:33页文件大小:687.0 KB来源: 弹性力学ppt课件

本课件围绕薄板弯曲的概念与计算假定展开,给出薄板的概念与小挠度弯曲计算假定,推导弹性曲面的微分方程与薄板横截面上的内力表达式。页面按板书顺序逐页呈现推导过程与结论,方便对照教材复习、自查解题步骤与公式来源。

薄板的弯曲目录页,依次列出薄板的概念与计算假定、弹性曲面的微分方程、薄板横截面上的内力等各节内容
薄板的概念与计算假定页,有关的概念及计算假定(1)由两个平行平面和垂直于这两个平行面的柱面或棱柱面所围成的图形,称为板
3)板上的荷载一般都分解页,本页为薄板的概念与计算假定的公式推导与板书图示
查看本课件的文字版(共 33 页,供检索与复制)

第1页:本章导读与目录

12.1 Introduction and Assumptions12 Bending of Thin Plates12.2 Differential Equation for Bending of Thin Plate12.3 Stress Resultants and Stress Couples12.4 Boundary Conditions12.5 A Simple Solution for Elliptical Plates12.6 Navier's Solution by Double Trigonometric Series12.7 Levy's Solution by Single Trigonometric Series

第2页:薄板的概念与计算假定

有关的概念及计算假定(1)由两个平行平面和垂直于这两个平行面的柱面或棱柱面所围成的图形,称为板。

两平行面
板面,柱面称为板边,板面之间的垂直距离称为板厚,平分板厚的平面称为板的中面.(2)若板厚t<<最小板边,称为薄板,否则称为厚板,根据板的形状,可分为矩形板,圆形板等12.1 Introduction and Assumptions一、薄板的特点:Thin Plates A plate is a body bounded by two closely spaced parallel planes andone or more prismatical surfaces normal to the planes.The parallelplanes form the two faces of the plate and the prismatical surfacesform the edges of the plate. The distance between the two faces,denoted by t, is called the thickness of the plate. The plateparallel to the faces of the plate and bisecting the thickness t iscalled the middle plane of the plate.A plate is said to be"thin"when its thickness is small incomparison with the dimensions of its faces.

第3页:3)板上的荷载一般都分解

(3)板上的荷载一般都分解为:平行于板面的荷载;垂直于板面的荷载xyzot/2 t/2(4)平行于板面的荷载沿板厚不变,按平面问题计算;垂直于板面的荷载引起弯曲,按薄板弯曲理论计算Any one of the loads acting on the plate can always be resolved intotwo components,one in the middle plane,called longitudinal load, andthe other perpendicular to the middle plane,called transverse load.The longitudinal loads acting on the thin plate may be considered asuniformly distributed across the thickness of the plate,can

The transverse loads acting on theplate will cause bending of the plate,which will be discussed in thischapter.

第4页:薄板弯曲的基本假定(1)薄板弯曲时

二、薄板弯曲的基本假定(1)薄板弯曲时,中面为曲面,称为弹性曲面或中曲面,中面内各点在垂直方向的位移称为挠度.(2)小挠度弯曲:挠度<<t,(本章讨论)大挠度弯曲:挠度=t薄膜问题:挠度>>t(3)薄板弯曲的基本假定:(a)、假定应变分量εz=0,γxz=0,γyz=0(assumptions)The transverse displacement of a point on the middle plate is calledthe deflection of the point.The plate is bent with small deflection,i.e,the deflection is muchsmaller than the thickness.The normal strain in the transverse direction,εz, may beneglected.

第5页:由此假定推出下列结论

由此假定推出下列结论:xyzot/2 t/2说明任意根法线上,薄板全厚的所有各点具有相同的挠度All the points aligned on anormal to the middle plane willhave the same displacement inthe transverse direction andthat this displacement is justthe deflection of the plate.(b) The normals to the middle plane before bending remain normal tothis plane after bending.

This implies that the shearing strainsγxzandγyzare small enough to be neglected.

So,

第6页:弯曲变形前垂直于中面的法线

结论:弯曲变形前垂直于中面的法线,变形后仍为直线,且长度不变,称为直法线假定,它和梁弯曲的平面假定类似(c)、薄板弯曲时,垂直于板面的应力分量σz很小,可以忽略不计,纵向间无挤压,所以物理方程与平面问题的物理方程完全一样The normal stressσzis much smaller thanσxandσy,so thatσzmay beneglected

第7页:中面内各点的水平位移

(d)、中面内各点的水平位移u、v和w相比很小,可以忽略不计,即The longitudinal displacements of the points in the middle planemay be neglected.

第8页:Since说明中面无应变发生中面的位移

Since说明中面无应变发生中面的位移w(x,y)称为挠度函数以上假定在许多工程实际问题的分析中,已得到广泛应用Thus, the middle plane of the plate remains unstrained, althoughthe plane becomes curved after bending.

第9页:弹性曲面的微分方程

10.2弹性曲面的微分方程薄板的小挠度弯曲问题,采用按位移求解,所以,取薄板挠度w为基本未知量一、用w表示应力,应变和位移Differential Equation for Bending of Thin Plate In solving bending problems of thin plates, we take the deflectionw as the basic unknown function.

第10页:又应变分量

又应变分量:Strain components

第11页:又应变分量(续)

应力分量:Strain components

第12页:推导弹性曲面的微分方程在这里

二、推导弹性曲面的微分方程在这里,不存在纵向体积力:X=Y=0由平衡方程中的前两式:To express the stress components in terms of w ,we have to use thedifferential equations of equilibrium instead of physical equations.Noting that only transverse loads are considered here.

第13页:τxy的表达式代入

将σx、σy、τxy的表达式代入得:

第14页:将上两式积分得,由边界条件确定

将上两式积分得:由边界条件确定F1(x,y),F2(x,y)Using the boundary conditions on the lower and upper faces of theplate

第15页:将上两式积分得,由边界条件确定(续)

F1(x,y),F2(x,y)最后得:由平衡方程中的第三式:

第16页:将上两式积分得,由边界条件确定(续2)

取Z=0,或Z不为零时,将其转化为面力

第17页:根据边界条件求

积分得:根据边界条件求f3(x,y)边界条件:板下面求出f3(x,y),最后得Using the boundary conditions on the lower face of the plate

第18页:边界条件,板上面将

边界条件:板上面将σz的表达式代入此边界条件,得:or或写成:其中:称为薄板的弯曲刚度,量纲为:力·长度Using the boundary conditions on the upper face of the plate Where q is the total transverse load per unit of the plate,including the surface forces and the body forces in the z direction.Is called the flexural rigidity of the plate and has a dimension of[force][length].

第19页:方程称为薄板的弹性曲面微分方程或挠曲微分

求解时,按薄板侧面的边界条件,由此方程求w,然后按前述公式求应力分量若体力Z不为零,我们把每单位面积内的体力和面力都归入薄板上面的面力,用q表示Equation is the basic differential equation for bendingof thin plates under transverse loads. If we succeed in finding thesolution for w from this equation under boundary conditions on theedges of the plate,the stress components are readily found .这样处理只会对次要应力σz引起误差,对其他的应力分量无影响

方程
薄板的弹性曲面微分方程或挠曲微分方程,它是薄板弯曲的基本微分方程

第20页:薄板横截面上的内力

薄板横截面上的内力在大多数情况下,要使应力分量在边界上精确地满足边界条件是很困难的,只能用圣维南原理,使这些应力分量所组成的内力整体地满足边界条件现在,我们来讨论应力分量所组成的内力12.3 Stress Resultants and Stress Couples In most cases, it is impossible to satisfy the pointwise stressboundary conditions on the edges of a plate. We can satisfyonly the boundary conditions in terms of the stress resultantsand stress couples.

第21页:从薄板取平行六面体

从薄板取平行六面体,其边长为dx,dy,t在x为常量的侧面上,应力分量为:σx、τxy、τxz由于σx、τxy均与z成正比,所以,它们在薄板全厚上代数和分别为零,只能合成为弯矩和扭矩

第22页:横截面单位宽度

横截面单位宽度上,应力分量σx合成为弯矩:横截面单位宽度上,应力分量τxy合成为扭矩:

第23页:τxz合成为剪力

τxz合成为剪力:在y为常量的侧面上,应力分量为:σy、τyx、τyz每单位宽度内的σy、τyx、τyz合成为弯矩,扭矩和横向剪力:

第24页:

第25页:从薄板取平行六面体

从薄板取平行六面体,其边长为dx,dy,

第26页:薄板横截面上的内力可写

由于:所以,薄板横截面上的内力可写为:

第27页:应力分量的表达式

应力分量的表达式:

第28页:由应力分量的表达式可以看出

由应力分量的表达式可以看出:σx、σy、τxy的最大值发生在板面,τxz、τyz的最大值发生在中面,σz最大值发生在板面上,各应力的最大值分别为:

第29页:

第30页:以上提到的量纲都是作用在单位宽度上的力

注意:以上提到的量纲都是作用在单位宽度上的力,所以力矩的量纲为"力",剪力的量纲为"力/长度"正应力σx、σy分别与弯矩成正比,称为弯应力剪应力τxy与扭矩成正比,称为扭应力τxz、τxy与剪力Qx、Qy成正比,称为剪应力σz与q成正比,称为挤压应力

第31页:薄板的弯曲问题

薄板的弯曲问题中,由荷载引起的弯应力和扭应力最大,为主要应力;剪应力较小,是次要应力;挤压应力更小,是更次要应力。在计算薄板的弯曲问题时,主要计算弯矩和扭矩,横向剪力一般无须计算归纳计算薄板的弯曲问题,最终归结为,由方程

第32页:求挠度w,然后根据公式

求挠度w,然后根据公式:求弯矩、扭矩和剪力

第33页:最后根据下列公式求应力

最后根据下列公式求应力:注意:满足弹性曲面微分方程的位移及由此求出的弯矩、扭矩、剪力应该满足相应的位移边界条件和应力边界条件

顶部目录