首页基础学科包装技术包装技术基础 15 Lesson 15 Seven Steps for Cushioned Package Development第15课 缓冲包装设计七步法 (含FLASH动画).ppt

15 Lesson 15 Seven Steps for Cushioned Package Development第15课 缓冲包装设计七步法 (含FLASH动画).ppt

页数:35页文件大小:268.5 KB来源: 包装技术基础ppt课件

本课件按七步法展开缓冲包装设计流程,从确定产品脆值、明确流通条件与跌落高度,到计算缓冲衬垫尺寸、识别设计约束、制作原型测试与投产后的性能监测,给出工程化设计路径。

第15课缓冲包装设计七步法内容讲解页,围绕Package Development第15课缓冲包装设计七步法展开,属缓冲包装设计导引章节内容
引言要点页,列出Packaging can…、The procedure…等主要内容
引言内容讲解页,围绕1.Determine Product Fragility展开,属缓冲包装设计导引章节内容
查看本课件的文字版(共 35 页,供检索与复制)

第1页:第15课缓冲包装设计七步法

第15课缓冲包装设计七步法:Package Development第15课缓冲包装设计七步法

本页以图示为主,源文件仅提取到图题或标题文字「第15课缓冲包装设计七步法」,建议对照原课件图片补充本页要点说明。

第2页:引言

  • Packaging can be unnecessarily expensive ina couple of ways:1. Inadequate design results in shipmentdamage2. Over-design or poor design (more protectionthan is required or materials being incorrectly…
  • The procedure can be broken down intoseven basic steps.

第3页:引言

引言:Determine Product FragilityDetermine the amount of mechanical shock theproduct can survive on its own by evaluating “fragility”or “g-factor ”.

2. Determine ConditionsConsider the handling and transportation environmentthe product will face and establish the amount ofshock the product may encounter (“drop height”).

3. Calculate Cushion RequirementsUse dynamic cushioning curves to determinethickness, static loading and bearing area.

第4页:引言

引言:Recognizing Design ConstraintsCheck for important problems including compressivecreep, cushion buckling and extreme temperatureeffects.

5. Design Prototypes and TestBuild a prototype and determine its actualperformance. 6. Consider Vibration EffectsDetermine the natural frequency of any componentwhich is prone to vibration damage, and compare itagainst the vibration characteristics of your packagedesign.

第5页:Monitor PerformanceMonitor

本页源文件仅提取到动画占位标记,建议对照原课件动画补充本页要点说明。

本页以图示为主,源文件仅提取到图题或标题文字「Monitor PerformanceMonitor」,建议对照原课件图片补充本页要点说明。

第6页:脆值

脆值:Fragility is normally expressed in units of “g’s” andindicates the maximum deceleration the product canwithstand without being damaged.

The more fragile aproduct is, the lower its g-factor(Table 15. 1).

第7页:包装件脆值分级

表15.1 典型包装件的脆值近似分级
脆值等级G 值范围典型产品示例
极易损15~25 g飞机高度表、陀螺仪、精密机械装配件
很精密25~40 g医疗诊断设备、X 射线设备
精密40~60 g显示终端、打印机、测试仪器、硬盘驱动器
中等精密60~85 g音响与电视接收机、软盘驱动器
中等坚固85~115 g大型家用电器、家具
坚固115 g 以上台锯、缝纫机、机床

数据修正:源文件该表 G 值因无换行出现排列错位,已按脆值等级的标准对应关系校正顺序。

第8页:第1步 确定产品脆值

  • The highest deceleration, which did not cause damage,is then known to be the product’s g-factor.
  • It may be necessary to determine fragility levels for aproduct in various orientations.
  • If the g-factor is estimated too high, and the product isunable to survive as much shock as anticipated, thepackaging will be underdesigned and significantshipping damage is likely to occur.
  • If the g-factor is estimated too low, and the productcan actually withstand more shock than anticipated,the packaging will be overdesigned and unnecessarilyexpensive.

第9页:Drop heights are generally

Drop heights are generally:Drop heights are generally established by the product'sweight, which usually reflect how the product will behandled(Table 15. 2).

第10页:典型跌落高度

表15.2 典型跌落高度(按重量与搬运方式)
毛重范围(磅)搬运方式跌落高度(英寸)
0~10单人抛掷42
10~20单人搬运36
20~50单人搬运30
50~100双人搬运24
100~250轻型设备18
250 以上重型设备搬运12

源文件附注:托盘集装的产品跌落高度可达 6 英寸。

第11页:第3步 计算缓冲要求

  • To determine the amount of functional cushioningmaterial which will provide adequate protection for thepackaged item.
  • By functional cushioning material, we mean thatportion of the design which directly supports the loadand functions to absorb shock during impacts.

第12页:Determining Cushion

Determining Cushion:Determining Cushion Thickness 24" drop height, 2-5 drop average

第13页:Determining Static Loading

Determining Static Loading:Determining Static Loading Range 24" drop height, 2-5 drop average

第14页:典型结构

典型结构:Figure 15. 1Typical dynamic cushioning curve

本页以图示为主,源文件仅提取到图题或标题文字「典型结构」,建议对照原课件图片补充本页要点说明。

第15页:第3步 计算缓冲要求

  • Curves are generated by dropping a series of knownweights onto a cushion sample from a specified heightand measuring the amount of shock experienced bythe weights as they impact the foam.
  • In simple terms, this testing represents a productdropping on a cushion from a height likely to beencountered during shipment.
  • The horizontal axis represents a range of staticloadings that packaged items might apply to thecushioning material. The vertical axis represents theshock experienced as the cushion is impacted.

第16页:第3步 计算缓冲要求

  • Curves are often presented for both first impact andmultiple impact (average of drops 2-5) data.An Example
  • Given] An object to be packaged is a 10-inch cubeweighing 60 pounds with a fragility of 50 g's.
  • Solution]1. Since a product typically faces repeated impactsduring shipment, you will probably wish to usemultiple-impact data.2.The typical drop height for a product of this weightmay be estimated f…

第17页:第3步 计算缓冲要求

  • locate our product's fragility level (50 g's) on thevertical axis of the figure, and draw an imaginaryhorizontal line across the chart at this level.Thisseparates the chart into two sections:
  • our fragility line and lower, where the packaged itemwill be able to survive the anticipated shock level, and
  • the section above our line where the shock levels arehigh enough to damage the product

第18页:第3步 计算缓冲要求

  • choose a thickness of 2 inches for the thinnest cushionthickness.5. Determining Static Loading and Bearing Area
  • The useable part of the curve is bounded by a staticloading of 0.3 psi at the low end, and 1.4 psi at thehigh end. This tells us that, with a 2-inch cushion, wecan apply a static loading anywhere wit…
  • The highest static loading value within the cushioningrange will result in the most economical designbecause it will use less cushioning material to provideadequate protection, thus lowering design c…

第19页:The cushion bearing area

  • The cushion bearing area is easily calculated as theproduct weight divided by our chosen static loading.a) 60 / 0.3 = 200 square inches of foamb) 60 /1.4 = 43 square inches of foam (This is a 78.5%re…
  • Designing to the minimum thickness is the generalpractice.
  • By repeating this procedure with several materials,you can quickly generate comparisons, which willallow you to strike an economical balance betweenmaterial cost and package size.

第20页:第4步 识别设计约束

  • Compressive creep is the gradual loss of thickness amaterial may experience if placed under a constantload for an extended period of time.
  • Significant compressive creep will result in thepackaged product loosening in the cushion andbecoming vulnerable to excessive movement insidethe package during shipment.

第21页:As a general rule, creep

  • As a general rule, creep of 10% is recognized as apractical upper limit. In some cases creep losses ofover 10% in thickness have been shown to result in asignificant loss of cushion performance.
  • Should it be found that creep in excess of 10% isanticipated, designers should recalculate thefunctional foam requirement using a lower static-loading figure. Spreading the loading over a largerarea …

第22页:第4步 识别设计约束

  • Buckling is the non-uniform compression of a cushion.
  • When buckling occurs, the energy of the impact is nottransferred evenly throughout the cushion and moreshock is transferred to the package contents.
  • Buckling usually occurs when the cushions becometoo tall and thin.
  • Figure 15.2 provides width-to-thickness coefficients fordifferent static loading values and enable the designerto check for buckling potential.Figure 15.2 Buckling coefficients for ETHAFOAM

第23页:第4步 识别设计约束

第4步 识别设计约束:Buckling Coefficients for ETHAFOAM 220 at Various Static Loadings

第24页:第4步 识别设计约束

第4步 识别设计约束:Buckling Coefficients forETHAFOAM Select at Various Static Loadings

第25页:第4步 识别设计约束

第4步 识别设计约束:Buckling Coefficients for ETHAFOAM Nova at Various Static Loadings

第26页:示例

  • Example: Let's assume you plan to use a 3-inch thickpad of ETHAFOAM 220 to cushion a side of yourproduct, which presents a static load of 1.0 psi.
  • In this case, the coefficient is 0.7. Using the formula Tx W/T = W, you can now find the minimum width: 3"x0.7 = 2.1". Your cushion must be at least 2.1 incheswide or long to resist buckling.3. Consi…

第27页:第4步 识别设计约束

  • As with all thermoplastic foams, when they areexposed to extremely high or low temperatures over aconsiderable length of time, they may be affected.
  • The materials become stiffer at low temperatures andincreasingly softer at higher temperatures. In extremecases, it may become necessary to compensate forthese effects in your design.

第28页:第5步 原型制作与测试

  • Each packaging design must be developedseparately, given the large number of variablesinvolved.
  • It is highly recommended that you build andtest a prototype of your cushion design todetermine its actual performance.

第29页:运输工具激励频率

表15.3 典型运输工具的激励频率范围
运输工具频率范围条件
铁路2~7 Hz(悬挂)运行中的货运车厢
铁路50~70 Hz(结构)运行中的货运车厢
卡车2~7 Hz(悬挂)正常公路行驶
卡车15~20 Hz(轮胎)正常公路行驶
卡车50~70 Hz(结构)正常公路行驶
飞机2~10 Hz(螺旋桨)飞行中的机舱地板
飞机100~200 Hz(喷气)飞行中的机舱地板
船舶11 Hz(甲板)船体水流干扰及螺旋桨轴系不平衡与不对中引起的振动
船舶100 Hz(舱壁)船体水流干扰及螺旋桨轴系不平衡与不对中引起的振动

第30页:第6步 考虑振动影响

  • Every mode of transport subjects the packages beingshipped to some amount of vibration at variousfrequencies.
  • In order to provide products which are prone tovibration damage with protection against such effects,it is essential to determine the natural frequency of anycomponent which is prone to vibration dam…
  • Every cushioning system has a range of vibrationalfrequencies in which it amplifies vibration and passeson a more severe vibration to the packaged productthan it receives from the transport environme…

第31页:For most vibration-sensitive

  • For most vibration-sensitive products, making surethat the package design does not amplify vibration inthe product's natural frequency and is enough toprevent vibrational damage from occurring during…
  • For severely vibration-sensitive products, it may benecessary for the package design to actually attenuatethe frequencies of concern.

第32页:Typical vibrational

典型结构:Figure 15. 3 Typical vibrational response of a package

本页以图示为主,源文件仅提取到图题或标题文字「Typical vibrational」,建议对照原课件图片补充本页要点说明。

第33页:Vibrational

Vibrational response:Figure 15. 4 Vibrational response of a cushioning material

第34页:第6步 考虑振动影响

第6步 考虑振动影响:Material response is often given in diagrams similar toFigure 15. 4, which represent performance for a giventhickness of material.

Note that for any frequency, onecan estimate whether the package will perform indirect coupling, amplification, or attenuation mode as afunction of the static loading applied to the cushion.

第35页:Step 7 Monitor Performance Ifit

  • There are many assumptions that went into yourdesign development.
  • It is a good practice to monitor the performance ofyour design in actual use. This will help you todetermine if your design is providing more real-worldperformance than is actually required, or not e…
  • Monitoring of packaging performance on an ongoingbasis can also help determine if further economies canbe achieved without sacrificing protection.
顶部目录