首页基础学科包装技术包装技术基础 05 Lesson 5 Metal Containers第5课 金属容器.ppt

05 Lesson 5 Metal Containers第5课 金属容器.ppt

页数:33页文件大小:893.5 KB来源: 包装技术基础ppt课件

本课件介绍金属容器,从钢材与铝材的材料背景与成型优势讲起,展开常见金属容器形状、三片罐与两片罐的制造工艺、罐盖与双卷边结构,并延伸介绍气雾剂包装的原理与推进剂类型。

第5课金属容器章节标题页,涵盖Steel is one of the older packaging mate等小节内容
Steel is one of the older内容讲解页,围绕Steel is one of the older packaging展开,属金属容器的材料背景章节内容
背景概述示意图页,展示该图对应的设备或工艺结构与工作过程
查看本课件的文字版(共 33 页,供检索与复制)

第1页:第5课金属容器

第5课金属容器:本页为该章节的标题页,标示本节主题与后续内容的展开方向。

本页以图示为主,源文件仅提取到图题或标题文字「第5课金属容器」,建议对照原课件图片补充本页要点说明。

第2页:Steel is one of the older

Steel is one of the older:Steel is one of the older packaging materials.-Originally used for round, square, and rectangularboxes and canisters.-The old-fashioned appearance of a fabricated metalbox is effectively used to create nostalgia for specialtyand gift-type containers.-Sanitary food can, hand-soldered cylindrical metal cansstarted in the early l800s.-Metal cans’ advantages:

第3页:背景概述

背景概述:being relatively inexpensivecapable of being thermally

本页以图示为主,源文件仅提取到图题或标题文字「背景概述」,建议对照原课件图片补充本页要点说明。

第4页:Three-piece (left)

背景概述:Figure 5. 1 Three-piece (left) and two-piece(right) can construction

第5页:Shallow drawn containerswith

Shallow drawn containerswith:Shallow drawn containerswith friction or slip covers-Two-piece shallow drawn cans with double-seamed(folded) ends-Two-piece cans(Figure 5.

1).reduced metal usageimproved appearanceelimination of a possible leakage locationmore elaborate tooling required-Deeper draws and multiple draws and draw-and-ironprocess-Impact-extrusion: tin, lead, and Al; collapsible tubes(nearly Al); heavier gauge aluminum extrusions used forpressurized aerosol containers

第6页:常见金属容器形状

  • Aerosol cans, made by two methods: (1) Three-piecesteel cans with a welded body and two ends, and (2)one-piece, impact-extruded aluminum cans necked-into accept the valve cup.
  • Steel or aluminum two-piece drawn-and-ironedbeverage cans.
  • Two-piece steel or aluminum cans by drawing or bydraw and redraw.Full-opening, ring pull-top cansDouble-seamed, conventional-top cans
  • Cans with hinged lids, usually steel

第7页:常见金属容器形状

  • Three-piece steel or aluminum ovals, typically fitted with a dispensingspout (Figure 5.2)
  • Traditional pear-shaped, three-piece steel ham cans
  • Oblong steel three-piece F-style cans (Figure 5.2)
  • Oblong key-opening cans, three-piece steel
  • Multiple friction cans of three-piece steel, also referred to as double-andtriple-tight cans
  • Three-piece, square-breasted steel cansSpice cans (smaller three-piece cans) with a perforated metal orplastic top
  • Industrial pails and drums
  • Two-piece, low-profile steel or aluminum ovals, with full-opening ringpull-tops

第8页:Examples of

示例:Figure 5. 2 Examples of specialized can shapes

本页以图示为主,源文件仅提取到图题或标题文字「Examples of」,建议对照原课件图片补充本页要点说明。

第9页:三片钢罐

三片钢罐:Steel three-piece can bodies can be mechanicallyseamed, bonded with adhesive, welded, or soldered(Figure 5. 3).-Aluminum cannot be soldered and cannot be weldedeconomically.-Welded sanitary three-piece can bodies are thereforemade exclusively of steel.-Mechanical seaming or clinching is used only forcontainers intended for dry product

第10页:Mechanical, welded

三片钢罐:Figure 5. 3 Mechanical, welded, and adhesive-bonded sideseams for three-piece cans

第11页:三片钢罐

三片钢罐:Adhesive bonding, or cementing, uses a thermoplasticadhesive extruded onto a hot can blank. Being anattractive body-assembly method for not being subjectedto thermal processing having full wraparoundlithographyi.e.,three-piece beverage containers ,some frozen juiceconcentrate and paint cans-Soldered a can, (solders : 97.

5% lead and 2. 5% tin). Lead extraction by food products and a potential problemwith soldered seams Being no longer permitted for food inNorth America-Welded cans, (strong and eliminate potential leadhazards).

第12页:工艺流程

工艺流程:Process:(Notes: Soudronic-the global leader forresistance and laser welding systems and key productionsystems for the metal packaging industry (3-piece cans,industrial packaging)body sheet-a tube with a slight overlap-passingbetween electrodes-an electrical current heats andfuses the metal (Figure 5.

4). Welded seam: about 30% thicker than the two basemetal sheets.-Sanitary food cans and bead: to improve resistance tocollapse (preventing collapse during pressuredifferentials encountered during retorting and enables thecan to withstand an internal vacuum).

第13页:The can-welding

The can-welding:Figure 5. 4 The can-welding process

本页以图示为主,源文件仅提取到图题或标题文字「The can-welding」,建议对照原课件图片补充本页要点说明。

第14页:侧壁压筋

侧壁压筋:Sidewall beading:requires more materialreduces top-to-bottom compression strengthcomplicates labeling-Can ends intended for thermal processing and a seriesof circular expansion panels (Figure 5.

5). This allows for movement of the end panels so that thecontents are able to expand and contract without bulgingor otherwise distorting the can.-Can-end compound applied around the perimeter curlas a caulk or sealant (Figures 5. 6 and 5. 7).

第15页:Typical can-end

罐盖结构:Figure 5. 5 Typical can-end embossing pattern

本页以图示为主,源文件仅提取到图题或标题文字「Typical can-end」,建议对照原课件图片补充本页要点说明。

第16页:Double-seaming is

三片钢罐:Figure 5. 6 Double-seaming is the attachment of the can end to thebody. It involves two curling steps.

第17页:The double seam is

The double seam is a critical:Figure 5. 7 The double seam is a critical can component. Every angle, radius, anddimension must be correct to ensure a hermetic seal

第18页:拉深与再拉深

拉深与再拉深:Draw and redraw (DRD) Draw and iron (D&I )DrawProcess:Shallow-profile cans(whoseheight is less than their diameter)can be drawndirectly from a circular metal blank.

The processis sometimes referred to as "shallow draw."Blanks for drawn cans may be decorated prior todrawing (Figure 5. 8)

第19页:Straight lines

两片罐:Figure 5. 8 Straight lines become distorted in different directionsduring drawing

第20页:两片罐

两片罐:Draw-and-redrawProcess:The first draw produces ashallow cup. The second reduces the diameter as thecan is deepened. Cans having a height significantlygreater than the can diameter would require a third draw.

Draw-and-ironProcess: Carbonated beverage cans byD&I process (Figures 5. 9, 5. 10). The thin walls of the D&Icontainer’s usage:not undergo severe thermal processinglend support to the wallsi.e., carbonated beverage cans ,noncarbonatedjuices,soft drink can use either steel or aluminum, beer isparticularly sensitive to traces of dissolved iron whilebeing relatively insensitive to aluminum.

第21页:The manufacturing sequence

本页源文件仅提取到动画占位标记,建议对照原课件动画补充本页要点说明。

本页以图示为主,源文件仅提取到图题或标题文字「The manufacturing sequence」,建议对照原课件图片补充本页要点说明。

第22页:The second draw and

两片罐:Figure 5. 10 The second draw and the ironing stages are allaccomplished in one continuous movement. The punch and theironing rings are shown in this exaggerated illustration. The punchfinishes its stroke against the bottoming tool

第23页:冲击挤压

冲击挤压:Impact extrusion forms ductile metals such as tin, lead,and aluminum into seamless tubes.-Tin's high cost prohibits its use except for collapsibletubes for certain pharmaceuticals.-Lead, is now used only for applications where itschemical inertness is an asset.-Most impact extrusions are made from aluminum.-Impact-extrusion sequence (Figure 5.

11)slug-striking-metal flowing up-a round, cylindricalshape(tube height up to seven times its diameter)

第24页:Impact-extrusion

冲击挤压成型:Figure 5. 11 Impact-extrusion sequence

本页以图示为主,源文件仅提取到图题或标题文字「Impact-extrusion」,建议对照原课件图片补充本页要点说明。

第25页:Typical

典型结构:Figure 5. 12 Typical impact-extruded tube tips

本页以图示为主,源文件仅提取到图题或标题文字「Typical」,建议对照原课件图片补充本页要点说明。

第26页:冲击挤压成型

  • the best barrier to all gases and flavors.
  • the best dead-fold characteristics (ability to be flattened or rolled up).
  • being decorated in a manner that takes advantage of their metalliccharacter.

第27页:冲击挤压成型

冲击挤压成型:having a wide range of lining options because of

本页以图示为主,源文件仅提取到图题或标题文字「冲击挤压成型」,建议对照原课件图片补充本页要点说明。

第28页:Two impact-extruded

Two impact-extruded aerosol:Figure 5. 13 Two impact-extruded aerosol can designs(left, center)and a three-piece welded-steel aerosolcan(right). All aerosol cans have bottoms that aredomed upward against internal pressure

第29页:气雾剂包装

气雾剂包装:Aerosol packaging refers to products packaged in a

本页以图示为主,源文件仅提取到图题或标题文字「气雾剂包装」,建议对照原课件图片补充本页要点说明。

第30页:气雾剂推进剂

气雾剂推进剂:Aerosol Propellants.-A typical aerosol product has a liquid phase and a

第31页:In a two-phase

AEROSOLSFigure:In a two-phase aerosol, the propellant isdissolved in the product. In a three-phase system,the propellant forms a separate layer

第32页:工作原理

工作原理:Principle:suitable propellant & driving

本页以图示为主,源文件仅提取到图题或标题文字「工作原理」,建议对照原课件图片补充本页要点说明。

第33页:Aerosols with

AEROSOLSFigure:Aerosols with propellants in chambers separatefrom the product

顶部目录