首页基础学科包装技术包装技术基础 14 Lesson 14 Test Method for Product Fragility第14课 产品脆值试验方法.ppt

14 Lesson 14 Test Method for Product Fragility第14课 产品脆值试验方法.ppt

页数:19页文件大小:383.0 KB来源: 包装技术基础ppt课件

本课件讲解产品脆值的试验方法,介绍用冲击试验机绘制损伤边界曲线、用振动系统测定固有频率的完整流程,说明试验条件设置、数据判读方法,以及脆值结果在缓冲包装设计中的具体应用。

第14课产品脆值试验方法章节标题页,涵盖产品脆值试验方法、冲击、Damage BoundaryImplications 等小节内容
产品脆值试验方法要点页,列出A shock machine…、A vibration…等主要内容
冲击内容讲解页,源文件该页为连续粘连文本,建议对照原图核对要点
查看本课件的文字版(共 19 页,供检索与复制)

第1页:第14课产品脆值试验方法

第14课产品脆值试验方法:本页为该章节的标题页,标示本节主题与后续内容的展开方向。

本页以图示为主,源文件仅提取到图题或标题文字「第14课产品脆值试验方法」,建议对照原课件图片补充本页要点说明。

第2页:产品脆值试验方法

  • A shock machine is used to generate adamage boundary curve
  • A vibration system is used to map out thenatural frequencies of a product.

第3页:冲击

冲击:Damage BoundaryShock damage to products results from excessive internal stressinduced by inertia forces-SinceF=ma,shock fragility is characterized by the maximum tolerableacceleration level, i. e, how many g’s the item can withstand.-Why damaged?-How to reduce g’s ?

The packaging material changes the shock pulse delivered to theproduct so that the maximum acceleration is greatly reduced (andthe pulse duration is many times longer).-The package designer’s goal:To be sure that the g-level transmitted to the item by the cushion isless that the g-level which will cause the item to fail.

第4页:冲击

冲击:Damage BoundaryThe damage boundary theoryis used to determine which shockinputs will cause damage to a product and which will not.-Two parts of a shock can cause damage:1. the acceleration levelA2. the velocity change∆V(the area under the acceleration-timehistory of the shock, thought as the energy contained in a shock)-The critical velocity change(∆Vc): a minimum velocity changewhich must be achieved before damage to the product can occur.

1. Below∆Vc, no damage occurs regardless of the inputA2. Exceeding∆Vc, does not necessarily imply that damage results.a.

If∆Voccurs in a manner which administers acceptable doses ofacceleration to the product, the velocity change can be very largewithout causing damage.b.

第5页:损伤边界

损伤边界:Damage BoundaryImplications of Fig. 14. 1:a. if the input∆V<the product’s∆Vc, then theacceleration level of the input can be in the 100 G’s,1000 G’s, 10,000 G’s, or even without causingdamage.

In fact, the duration is so short that theproduct cannot respond the acceleration level of theevent, only the energy input.b. if the input ∆V>the product’s ∆Vc, However, the onlyway to avoid damage is to limit the input A < theproduct’s Ac.

This is usually one of the functions that acushioned package performs: it translates the highacceleration events experienced on the outside of thecontainer to lower acceleration events experiencedinside at the unit.

第6页:Typical damage

Damage BoundaryFigure:Damage BoundaryFigure 14. 1 Typical damage boundary curve

第7页:损伤边界

损伤边界:Damage Boundaryc. For∆V<∆Vc,area where damage does not occureven with very high accelerations. Here∆V(drop height)is so low that the item acts as its ownshock isolator.d. <Ac, damage does not occur, even for large∆V.

That’s because the forces generated (F =ma) are withinthe strength limits of the products.-From Fig. 14. 2,a.∆Vcboundary (vertical boundary line), is independentof the pulse wave shape.b.

Ac(to the right of the vertical line) for half sine andsawtooth pulses depends upon∆V.

第8页:Damage boundary

Damage BoundaryFigure:Damage BoundaryFigure 14. 2 Damage boundary forpulses of same peak acceleration andsame velocity change

第9页:损伤边界

损伤边界:Damage Boundaryc. The damage boundary generated with use of a trapezoidal pulseencloses the damage boundaries of all the other waveforms.-Fragility testingis the process used to establish damageboundaries of products.a.

It is usually conducted on ashock testing machine. Theprocedure has been standardized (ASTM D3332, Mechanical-ShockFragility of Products, Using Shock Machines).b.

Procedure:the item to be tested is fastened to the top of a shockmachine table and the table is subjected to controlled velocitychanges and shock pulses.

第10页:Damage Boundaryc

Damage Boundaryc:Damage Boundaryc. For trapezoidal pulses, the programmer is a constant forcepneumatic cylinder. Theg-levelof the trapezoidal pulse iscontrolled simply by adjusting thecompressed gas pressureinthe cylinder.

The∆Vis controlled by adjustingdrop height. A Shock Testing Machine (1)

第11页:脆值试验实施

脆值试验实施:To determine a damage boundary requires running two sets of tests.-Astep velocity testis used to determine the product’s∆Vcand astep acceleration testis used to determineAc.

1. Step Velocity Test( Figure 14. 3) to determine the vertical line ofthe damage boundary. 2. Step Acceleration Test(Figure 14.

4) to determine the horizontalline of the damage boundary..a. A new test specimen be attached to the shock table.b. The drop height is set at a level which will produce a velocitychange at least 1.

第12页:Velocity damage

Velocity damage boundary:Figure 14. 3 Velocity damage boundary development

第13页:脆值试验实施

脆值试验实施:A Shock Testing Machine (2)

本页以图示为主,源文件仅提取到图题或标题文字「脆值试验实施」,建议对照原课件图片补充本页要点说明。

第14页:脆值试验实施

脆值试验实施:Plot the damage boundary curve by connecting the verticalvelocity boundary line and the horizontal acceleration boundary line.

4. Notes:In a rigorous testing program, damage boundary curvesare generated for each orientation of the unit. Compromises areoften made to limit the number of units which must be damaged. Figure 14. 4 Damageboundary linedevelopment

第15页:共振搜索

共振搜索:Resonance Search & DwellIt is generally accepted that the steady-state vibration environment isof such low acceleration amplitude that failure does not occur due tonon-resonant inertial loading.-Damage is most likely to occur when some element or componentof a product has anatural frequencywhichis excited by theenvironment.-The identification of those frequencies becomes critical indesigning a package system.

The purpose of the bare productvibration testing is to identify the natural or resonant frequencies ofthe critical components within the product.-Response of a product or component to input vibration may berepresented by a curve similar to that shown in Figure 14. 5.

第16页:Typical resonant

Resonance Search &amp:Resonance Search & DwellFigure 14. 5 Typical resonant frequency transmissibility curve

第17页:共振搜索

共振搜索:Resonance Search & DwellVibration transmissibility curveshows:a. For very low frequencies, response acceleration is the same as theinput;b.

For very high frequencies, the response is much less than the input.c. But in between, the response acceleration can be many times theinput level.

This is the frequency range where damage is most likely tooccur.-How to identify the product and component resonant frequencies:a.

第18页:Resonance Search &

Resonance Search &amp:Resonance Search & DwellA Vibration Testing Machine (1)

第19页:共振搜索

共振搜索:Resonance Search & DwellA Vibration Testing Machine (2)

顶部目录